How A.R.E.'s Weathertight Seal System Actually Keeps Water Out of Your Truck Cap
A truck cap water seal isn’t a single rubber strip—it’s a coordinated system of compression seals, drainage paths, and structural fit that work together to keep your gear dry in driving rain or a pressure wash. Over the years we’ve refined our weathertight design to address the most common leak points: the cab-to-cap interface, side-rail contact, and corner transitions where geometry changes.
This guide walks through how each layer of our seal system functions, what sets a precision-fit seal apart from a generic compression strip, and how to inspect and maintain the components so they perform for the long haul.

The Dual-Bulb Seal at the Cab Interface
The primary seal between the cap and the truck cab uses a dual-bulb EPDM extrusion that creates two independent compression zones. The outer bulb deflects when the cap closes, forming the first barrier; the inner bulb compresses against the cab’s rear window frame, creating a backup seal if water breaches the outer layer.
EPDM resists UV degradation and ozone cracking better than standard neoprene, which matters because this seal sits in direct sun year-round. The material stays pliable through temperature swings from below freezing to desert heat, maintaining even contact pressure across the entire perimeter.
Why Two Bulbs Instead of One
A single-bulb seal relies on perfect alignment and consistent cab tolerances—neither of which exist in the real world. The second bulb accounts for cab flex, minor body panel variations, and slight settling over time, ensuring water can’t find a path through even if the outer seal compresses unevenly.
Side-Rail Contact and the Role of Tailgate Geometry
The side rails where the cap meets the truck bed use a continuous flat seal that runs the full length of each rail. This seal differs from the cab seal because it handles shear forces—wind pressure tries to lift the cap slightly at highway speed, and the seal has to maintain contact while flexing.
We engineer the bottom flange of the cap to match the bed rail width exactly, so the seal compresses uniformly without gaps at the corners. Trucks with spray-in bedliners require a slightly thicker seal because the liner adds material; we account for that in the fit and provide shims if needed.
The tailgate creates a fourth sealing surface that changes geometry when open versus closed. Our rear seal wraps the lower edge and extends down to meet the tailgate’s top surface, forming a compression joint when the gate latches. If you tow with the tailgate down, water can enter through this gap—that’s unavoidable physics, not a seal failure.
Drain Channels and the Front Header Design
Even a perfect seal will eventually see condensation or windblown mist reach the interior side. The front header above the cab window incorporates molded drain channels that collect any moisture and route it to exit points at the lower corners, outside the cargo area.
These channels are invisible from the outside but critical to long-term dryness. They prevent water from pooling against the seal’s interior face, which would eventually wick through via capillary action or freeze-thaw cycles.
Inspection Access
You can check the drain exits by looking under the front lower corners of the cap with a flashlight—you’ll see small weep holes. If these clog with dust or debris, moisture backs up and can seep into the cab seal joint. A quick flush with compressed air once a season keeps them clear.

Seal Maintenance and Longevity Factors
The seals themselves need minimal maintenance, but two habits extend their service life significantly. First, clean the contact surfaces—both the seal and the truck’s mating surfaces—every few months with soap and water to remove road grime and salt. Dirt acts as an abrasive and creates micro-gaps where water can wick through.
Second, apply a thin coat of silicone spray or rubber conditioner to the seals twice a year. This replaces plasticizers that UV exposure gradually pulls out of the EPDM, keeping the material supple. Avoid petroleum-based treatments; they soften the rubber temporarily but accelerate long-term degradation.
If you notice a persistent leak, check the clamp tension at the mounting points first. Caps settle slightly after installation, and retorquing the clamps to spec often solves the issue without replacing any seals. We publish torque values in the installation manual, and the same principles apply whether you’re looking at our LEER Locker truck cap or a fiberglass model—consistent clamp pressure ensures even seal compression around the entire perimeter.

How Precision Fit Reduces Leak Risk
Generic truck caps use adjustable mounting brackets and oversized seal channels to fit multiple truck models with one design. That flexibility comes at a cost: the seal has to bridge larger gaps and tolerate more misalignment, which means thicker, less precise compression.
Our caps are manufactured to match specific cab and bed dimensions, measured in millimeters rather than fractional inches. The tighter fit allows us to use thinner, more responsive seals that conform to the truck’s actual surface rather than just squashing flat under high clamp force.
This approach also reduces wind noise—a seal that’s compressed just enough to block water but not so much that it deforms creates a quieter ride than an over-compressed generic seal fighting against excessive clamp tension. The same precision that keeps water out also keeps road noise down.
Why the System Works as a Whole
A weathertight truck cap isn’t about one miracle seal—it’s about making sure every component does its specific job and the parts work together without fighting each other. The dual-bulb cab seal handles compression and backup; the side-rail seal manages shear and flex; the drain channels evacuate the moisture that does get past; and the precision fit reduces the burden on all of them.
When you maintain the seals, keep the clamps torqued, and flush the drains, the system performs for years without drama. The few minutes twice a year you spend on a visual check and a coat of conditioner will save you from discovering a leak the hard way when you open the cap after a rainstorm.
Common Questions About Truck Cap Seal Performance
Most seals last five to seven years with basic maintenance. Replace them sooner if you see visible cracking, permanent compression set where the seal no longer springs back, or if cleaning and re-torquing the clamps doesn’t stop a leak.
We stock replacement seals by model and year, and they install with the cap in place—no need to remove the entire unit.
Yes, as long as the seals are in good condition and the clamps are torqued to spec. The high-pressure jets in a touchless wash are a good real-world test.
If you do see water intrusion after a wash, it’s usually from the tailgate seal if the gate was left open, or from a loose clamp that let the cap lift slightly under the water pressure.
The two most common causes are leaving the truck parked in direct sun without any UV protection on the seals, and over-tightening the clamps during installation. Excessive clamp force deforms the seal permanently, and it loses the ability to recover and maintain contact pressure.
Chemical exposure—especially from harsh degreasers or solvent-based cleaners—can also break down EPDM faster than normal weathering.
No. The perimeter seals are accessible with the cap installed; you can clean, condition, or replace them by loosening the clamps enough to lift the seal edge.
The only exception is the front header drain channels, which are easier to flush thoroughly if you remove the cap, but you can still clear them in place with a long flexible brush or compressed air nozzle.
Run a hose along the suspect area and watch where water appears inside. Seal leaks show up as a wet line tracing the perimeter; leaks from a cracked window, loose door striker, or a body mounting hole will appear as isolated drips or puddles away from the seal line.
If water only appears during heavy rain but not with a hose test, check the drain channels—they may be clogged and allowing condensation to overflow into the cargo area.
It raises the bed rail surface by a few millimeters, which reduces seal compression slightly. We account for this by including thicker side-rail seals or shim kits with caps ordered for liner-equipped trucks.
If you add a liner after the cap is installed, contact us for the correct seal thickness for your model—using the original seal on a raised surface can leave a small gap that lets water in during heavy rain or washing.
